DX200 Ice Regulator
£292.00 RRP £349.00 In Stock
The SEAC DX 200 Regulator is an environmentally sealed regulator meeting CE EN250:2000 cold water rating. Forged brass first stage with a sanded chrome finish.
High Performance Balanced First Stage is completely environmentally sealed for total insulation from the cold water to prevent ice from forming inside the first stage. the flexible environmental seal allows ambient pressure to be transfered to the internal mechanism to balance the first stage; delivering an even interstage pressure no matter the depth.
Technopolymer Second Stage is lightweight but strong and metal components improve strength and cold water performance by acting as a heat-sync. Adjustable breathing effort and venturi switch let you customise breathing effort and prevent free-flows.
Angled Low Pressure Ports create more natural hose routing for a single cylinder so your hoses aren't strained or stick out; ruining your trim.
Lightweight Braided Hose has a higher burst pressure than conventional rubber hoses and are much lighter for travel.
CE EN250:2000 tested
- HP outlets: x2
- LP outlets: x4, of which x2 inclined at 20° and x2 inclined at 30°.
Weight : 1.08kg
Seac Sub DX200 Ice Regulator - Features
?This feature allows the diver to adjust the inhalation setting from the set level and increase the effort required to open the 2nd stage valve to deliver air.
?The venturi control affects how air flows in the 2nd stage. In it's positive position the flow of gas creates a vacuum against the diapragm, helping to open the valve. In it's negative position it will divert gas back against the diaphragm helping to close the valve. It is basically used to help prevent free flowing.
|Cold Water Rated|
?Cold water has adverse effects on regulators and can cause some to freeze so each regulator combination must be tested during manufacturing for their performance in different water temperatures.
Cold water is defined by EN250 as below 10°C. If a regulator combination cannot meet the performance standards below 10°C then they are only suitable for warm waters.
EN250 / (EN250A >10°C)
To pass the regulator must provide at least 62.5 L/min of air at 50M depth above 10°C.
|Cold & Warm Water|
?Environmentally sealed 1st stages offer greater protection against freezing when diving in cold water (below 10 degrees C)
Scubapro have a new method of cold water proofing their first stages called the eXtended Thermal Insulating System or XTIS which still allows water into the first stage but the internal parts that come into contact with the water are coated to prevent ice from forming.
?Unbalanced regulators are affected by the pressure in the cylinder, becoming slighty harder to breathe from when the pressure starts to drop.
Balanced regulators are not affected by the cylinder pressure or depth.
Over-balanced regulators achieve unprecedented performance by increasing your air supply the deeper you go providing the best breathe for deep divers.
|High Pressure Ports|
?High pressure ports supply the pressure gauge and wireless transmitters for dive computers
|Low Pressure Ports|
?Low pressure ports supply the 2nd stages and inflator hoses
?An Unbalanced second stage is simply a lever operated valve that is opened and closed as the diaphragm is pulled inwards by the vacuum that is created when the diver inhales. An unbalanced second stage is affected by increased pressure at depth, slightly increasing the effort required to open the valve.
A Balanced second stage overcomes the effects of increased pressure by utilising a balancing chamber. This chamber takes some of the work away from the spring mechanism, allowing a smaller spring to be used which results in an easier breathe. As the chamber uses air to balance the valve it maintains the same resistance as the diver descends and ascends, keeping the inhalation effort the same.
?All regulators need to be serviced to keep them in working order as the parts inside them age and wear over time and with use. Most regulators need to be serviced once a year or after 100 dives with normal recreational use to replace parts and re-balance.
Some regulators use more modern materials or mechanisms that allow them to extend the servicing interval that can save you some money in the long run.
|1 Year - 100 Dives|
|Weight in Grams (approx)|
?The weight includes the first stage (DIN fitting), hose and second stage.
We offer free standard delivery on orders over £50.
Standard delivery is £3.70 for orders under £50. You will receive your order 2 - 4 days from the date of despatch.
Next Working Day is £6.50.
We hope you will be completely satisfied with any product purchased from Simply Scuba.
However, you can return it for any reason within 28 days from the date of despatch for a full refund (less postage costs).