S620Ti 2nd Stage
£298.00 RRP £365.00 Out Of StockPlease note: This item cannot be shipped outside the European Union - learn more
The Scubapro S620Ti 2nd Stage is a smaller version of the S600 and combines many of the features from the rest of the Scubapro 2nd stage range for a more efficient regulator. A Titanium Barrel inside reduces weight and improves corrosion resistance for longevity.
By combining the best features of their existing second stages Scubapro created the S 620 that has the same large diaphragm from the S600 and a completely new exhaust tee for a reduction in work of breathing of 37%. All the new features and design mean the S620 has a smooth and easy breathe at all depths.
WHO IS THE S620Ti FOR?
The S620 is a higher-end 2nd stage suitable for any diver but it is focused towards advanced divers and those that appreciate higher performance. Smaller and lighter the S620 is fine for travelling and at home in cold waters too.
Compatible with any Scubapro 1st stage but better suited to the Mk25 and Mk17 to match it's performance.
The S620Ti 2nd stage is just the mouthpiece section of the regulator so you'll need a 1st stage and hoses.
The S620Ti is a higher end 2nd stage and one of their most modern mouthpieces but for a more basic 2nd stage for a stage cylinder you can look at the R195, lower specs than the S620 but a good little 2nd stage. For a more technical 2nd stage you can look at the G260, it's made to be tough and it's ambidextrous so you get a more flexible 2nd stage.
If you're looking to build a standard reg set then the S620 comes assembled on a 1st stage in this package:
|Weight (kg)||Measurements (cm)|
Scubapro dive gear is considered among the finest quality dive equipment and snorkel equipment available today and is used by many professional divers all over the world.
Scubapro's attention to detail is pinnacle with each piece of equipment so it performs perfectly in the water. Each part of their regulators is carefully crafted to improve airflow for a smooth breathe with minimal turbulence.
Scubapro S620Ti 2nd Stage - Features
?This feature allows the diver to adjust the inhalation setting from the set level and increase the effort required to open the 2nd stage valve to deliver air. Close.
?The venturi control affects how air flows in the 2nd stage. In it's positive position the flow of gas creates a vacuum against the diapragm, helping to open the valve. In it's negative position it will divert gas back against the diaphragm helping to close the valve. It is basically used to help prevent free flowing. Close.
|Cold Water Rated|
?Cold water has adverse effects on regulators and can cause some to freeze so each regulator combination must be tested during manufacturing for their performance in different water temperatures.
Cold water is defined by EN250 as below 10°C. If a regulator combination cannot meet the performance standards below 10°C then they are only suitable for warm waters.
EN250 / (EN250A >10°C)
To pass the regulator must provide at least 62.5 L/min of air at 50M depth above 10°C. Close.
|Cold & Warm Water|
?Environmentally sealed 1st stages offer greater protection against freezing when diving in cold water (below 10 degrees C)
Scubapro have a new method of cold water proofing their first stages called the eXtended Thermal Insulating System or XTIS which still allows water into the first stage but the internal parts that come into contact with the water are coated to prevent ice from forming. Close.
?Unbalanced regulators are affected by the pressure in the cylinder, becoming slighty harder to breathe from when the pressure starts to drop.
Balanced regulators are not affected by the cylinder pressure or depth.
Over-balanced regulators achieve unprecedented performance by increasing your air supply the deeper you go providing the best breathe for deep divers. Close.
|High Pressure Ports|
?High pressure ports supply the pressure gauge and wireless transmitters for dive computers Close.
|Low Pressure Ports|
?Low pressure ports supply the 2nd stages and inflator hoses Close.
?All regulators need to be serviced to keep them in working order as the parts inside them age and wear over time and with use. Most regulators need to be serviced once a year or after 100 dives with normal recreational use to replace parts and re-balance.
Some regulators use more modern materials or mechanisms that allow them to extend the servicing interval that can save you some money in the long run. Close.
|2 Year - 100 Dives|
We offer free tracked UK standard delivery on orders over £50.
Standard UK delivery is £3.95 for orders under £50. You will receive your order 2 - 4 days from the date of despatch. Order by 3pm on a working weekday and we will aim to despatch the same day.
Next Working Day for the UK is £6.95.
We hope you will be completely satisfied with any product purchased from Simply Scuba.
However, you can return it for any reason within 28 days from the date of despatch for a full refund (less postage costs).
Royal Mail tracked return option within the UK for your convenience.
Watch the video
Scuba regulator Advice
Choosing The Right Regulator
Looking for advice on choosing the right regulator?
Not a problem. Watch our video from our in-house expert Mark.
What To Buy DIN Or A-Clamp
Not sure which connection to go for?
Watch our video with Mark to learn which is best for you.
What Are Cold Water Regs
What makes a good cold water regulator?
Watch our video from our in-house expert Mark to find out what to look for.