Mk11 C370 Regulator
£228.00 RRP £269.00 In StockPlease note: This item cannot be shipped outside the European Union - learn more
The Scubapro Mk11 C370 Regulator is made to be a high-end travel regulator with greater performance than its predecessor. Compact and light the Mk11/C370 is balanced so you get a smooth breathe at any depth and won't take up much space in a bag.
MK11 First Stage:
Air balanced diaphragm design delivers constant and effortless airflow unaffected by depth, tank pressure, or breathing rate.
Marine brass body has internal parts that are sealed to prevent water and pollutants from fouling the inner mechanism while enhancing cold-water performance.
Two high pressure, two low pressure and two high-flow ports maximize hose routing options.
External intermediate pressure adjustment enables technicians to fine-tune performance quickly and easily.
Available in either 3364psi/232bar INT or 4350psi/300bar DIN configurations.
Weight: INT 232 - 24.4oz/692g; DIN 300 - 16.6oz/470g.
Airflow at 2900psi/200bar: 5500 l/min - 195 SCFM.
Intermediate pressure (psi/bar): 130-142/9.0-9.8.
C370 Second Stage:
Air-balanced valve smoothes out the inhalation effort at varying depths and supply pressures
Compact rugged fiberglass reinforced nylon casing and new exhaust tee take up little space in a dive bag
Stainless steel frame on the front cover adds the SCUBAPRO C-Series signature
A new poppet and lever allows the design to maintain the same overall size as the C350
A new exhaust tee based on the S620 Ti’s design contributes to better work of breathing (a 10% improvement over the C350)
User controls include a diver-adjustable inhalation effort knob and Venturi-Initiated Vacuum Assist (VIVA)
Large purge button is easy to activate, even wearing thick gloves.
Super-flow hose features an oversized bore that allows more air to flow on each inhalation
Compact Hi-Flow mouthpiece improves airflow as well as mouth comfort, fitting all mouth sizes, from smaller to largest
Airflow at 200bar: 1600 l/min
Scubapro Mk11 C370 Regulator - Features
?This feature allows the diver to adjust the inhalation setting from the set level and increase the effort required to open the 2nd stage valve to deliver air. Close.
?The venturi control affects how air flows in the 2nd stage. In it's positive position the flow of gas creates a vacuum against the diapragm, helping to open the valve. In it's negative position it will divert gas back against the diaphragm helping to close the valve. It is basically used to help prevent free flowing. Close.
|Cold Water Rated|
?Cold water has adverse effects on regulators and can cause some to freeze so each regulator combination must be tested during manufacturing for their performance in different water temperatures.
Cold water is defined by EN250 as below 10°C. If a regulator combination cannot meet the performance standards below 10°C then they are only suitable for warm waters.
EN250 / (EN250A >10°C)
To pass the regulator must provide at least 62.5 L/min of air at 50M depth above 10°C. Close.
|Cold & Warm Water|
?Environmentally sealed 1st stages offer greater protection against freezing when diving in cold water (below 10 degrees C)
Scubapro have a new method of cold water proofing their first stages called the eXtended Thermal Insulating System or XTIS which still allows water into the first stage but the internal parts that come into contact with the water are coated to prevent ice from forming. Close.
?Unbalanced regulators are affected by the pressure in the cylinder, becoming slighty harder to breathe from when the pressure starts to drop.
Balanced regulators are not affected by the cylinder pressure or depth.
Over-balanced regulators achieve unprecedented performance by increasing your air supply the deeper you go providing the best breathe for deep divers. Close.
|High Pressure Ports|
?High pressure ports supply the pressure gauge and wireless transmitters for dive computers Close.
|Low Pressure Ports|
?Low pressure ports supply the 2nd stages and inflator hoses Close.
?All regulators need to be serviced to keep them in working order as the parts inside them age and wear over time and with use. Most regulators need to be serviced once a year or after 100 dives with normal recreational use to replace parts and re-balance.
Some regulators use more modern materials or mechanisms that allow them to extend the servicing interval that can save you some money in the long run. Close.
|2 Year - 100 Dives|
|Weight in Grams (approx)|
?The weight includes the first stage (DIN fitting), hose and second stage. Close.
We offer free standard delivery on orders over £50.
Standard delivery is £3.95 for orders under £50. You will receive your order 2 - 4 days from the date of despatch. Order by 3pm on a working weekday and we will aim to despatch the same day.
Next Working Day is £6.95.
We hope you will be completely satisfied with any product purchased from Simply Scuba.
However, you can return it for any reason within 28 days from the date of despatch for a full refund (less postage costs).
Royal Mail tracked return option within the UK for your convenience.
Watch the video
Scuba regulator Advice
Choosing The Right Regulator
Looking for advice on choosing the right regulator?
Not a problem. Watch our video from our in-house expert Mark.
What To Buy DIN Or A-Clamp
Not sure which connection to go for?
Watch our video with Mark to learn which is best for you.
What Are Cold Water Regs
What makes a good cold water regulator?
Watch our video from our in-house expert Mark to find out what to look for.